A few things to keep in mind while
completing this activity:
1- Do not use the browser Back button or
close or reload any Exam windows during the exam.
2- Do not close Packet Tracer when you are
done. It will close automatically.
3- Click the Submit
Assessment button to submit your work.
Introduction
In this practice Packet Tracer Skills Exam,
you will:
- design and implement an addressing scheme to meet stated requirements
- configure, verify, and troubleshoot connectivity between all devices in the network
Addressing Table
Device
|
Interface
|
Address
|
Subnet Mask
|
Default Gateway
|
HQ
|
Fa0/0
|
10.10.10.1
|
255.255.255.192
|
n/a
|
Fa0/1
|
10.10.10.65
|
255.255.255.248
|
n/a
|
|
S2
|
VLAN1
|
10.10.10.2
|
255.255.255.192
|
10.10.10.1
|
NetAdmin
|
NIC
|
10.10.10.62
|
255.255.255.192
|
10.10.10.1
|
H1
|
NIC
|
Preconfigured
(10.10.10.67)
|
Preconfigured
(255.255.255.248)
|
Preconfigured
(10.10.10.65)
|
NOTE: The initial network has some errors. To aid in configuring and verifying the devices as well as troubleshooting the existing errors, use a printed version of these instructions to fill in the missing address information in the table during Step 1.
Step 1: Determine the IP Addressing
Scheme.
Design an addressing scheme and fill in the
Addressing Table based on the following requirements:
a. Subnet the address space 10.10.10.0/24 to
provide 40 host addresses for LAN 1 while wasting the least amount of address
space.
b. Assign the first available subnet to LAN 1.
c. Assign the lowest (first) host address in
this subnet to the Fa0/0 interface on HQ.
d. Assign the second address in this subnet to
the VLAN 1 interface on S2.
e. Assign the highest (last) host IP address in
this subnet to NetAdmin.
Step 2: Configure HQ.
a. Configure
HQ with these basic parameters:
· Use HQ as the
router name.
· Use class as the
encrypted password for privileged EXEC mode.
· Require password-protected logins for the
console line. Use cisco as the
password.
· Require password-protected logins for the
vty lines. Use cisco as the
password.
· Configure the banner message-of-the-day as Unauthorized
access is prohibited.
b. Configure the two Fast Ethernet interfaces:
· Configure the router interfaces according to
your completed Addressing Table.
· Configure each interface with a description.
c. Close the terminal window after completing
the router configuration.
Step 3: Configure S2 and Verify
Connectivity.
a. Remove the console connection between
NetAdmin and HQ.
b. Connect NetAdmin to the S2 console port.
c. Configure S2 with these basic parameters:
· Use S2 for
the switch name.
· Use class as the
encrypted password for privileged EXEC mode.
· Require password-protected logins for the
console line. Use cisco as the
password.
· Require password-protected logins for the
vty lines. Use cisco as the
password.
· Configure the banner message-of-the-day as Unauthorized
access is prohibited.
d. Configure interface VLAN 1.
e. Configure the default gateway.
f. Test that S2 is able to ping the default
gateway.
Step 4: Configure and Verify NetAdmin
Addressing.
a. Use the IP addressing you determined in Step
1 and configure NetAdmin with the correct addressing.
b. Test that NetAdmin is able to ping the
default gateway.
Step 5: Verify and Troubleshoot
End-to-End Connectivity.
Verify that NetAdmin is able to ping H1. If
the ping fails, locate and correct any errors. For example, make sure H1 is
configured correctly with appropriate addressing for the subnet it belongs to.
Packet Tracer image:
Step 2:
Configure HQ.
Press RETURN to get started!
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname HQ
HQ(config)#enable secret class
HQ(config)#line console 0
HQ(config-line)#password cisco
HQ(config-line)#login
HQ(config-line)#exit
HQ(config)#line vty 0 4
HQ(config-line)#password cisco
HQ(config-line)#login
HQ(config-line)#exit
HQ(config)#banner motd #Unauthorized access is prohibited.#
HQ(config)#interface fastEthernet 0/0
HQ(config-if)#ip address 10.10.10.1 255.255.255.192
HQ(config-if)#description LAN1
HQ(config-if)#no shutdown
HQ(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to
up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/0, changed state to up
HQ(config-if)#exit
HQ(config)#interface fastEthernet 0/1
HQ(config-if)#ip address 10.10.10.65 255.255.255.248
HQ(config-if)#description LAN2
HQ(config-if)#no shutdown
HQ(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/1, changed state to
up
%LINEPROTO-5-UPDOWN: Line protocol on Interface
FastEthernet0/1, changed state to up
HQ(config)#
Step 3: Configure S2 and Verify
Connectivity.
Switch>enable
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#hostname S2
S2(config)#enable secret class
S2(config)#line console 0
S2(config-line)#password cisco
S2(config-line)#login
S2(config-line)#exit
S2(config)#line vty 0 4
S2(config-line)#password cisco
S2(config-line)#login
S2(config-line)#exit
S2(config)#banner motd #Unauthorized access is prohibited.#
S2(config)#interface vlan 1
S2(config-if)#ip address 10.10.10.2 255.255.255.192
S2(config-if)#no shutdown
S2(config-if)#
%LINK-5-CHANGED: Interface Vlan1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1,
changed state to up
S2(config-if)#exit
S2(config)#ip default-gateway 10.10.10.1
S2(config)#exit
S2#
%SYS-5-CONFIG_I: Configured from console by console
S2#ping 10.10.10.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.10.1, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
31/34/47 ms
S2#write
Building configuration...
[OK]
S2#
